TANIGUCHI 40mm Lift Coil Springs Jimny JB74 (2018-ON)
TANIGUCHI 40mm Lift Coil Springs Jimny JB74 (2018-ON)
TANIGUCHI 40mm Lift Coil Springs Jimny JB74 (2018-ON)
TANIGUCHI 40mm Lift Coil Springs Jimny JB74 (2018-ON)
TANIGUCHI 40mm Lift Coil Springs Jimny JB74 (2018-ON)
TANIGUCHI 40mm Lift Coil Springs Jimny JB74 (2018-ON)
TANIGUCHI 40mm Lift Coil Springs Jimny JB74 (2018-ON)
TANIGUCHI 40mm Lift Coil Springs Jimny JB74 (2018-ON)
TANIGUCHI 40mm Lift Coil Springs Jimny JB74 (2018-ON)
TANIGUCHI 40mm Lift Coil Springs Jimny JB74 (2018-ON)
TANIGUCHI 40mm Lift Coil Springs Jimny JB74 (2018-ON)

We recommend these 40mm / 1.5" Lift Coil Springs as the best all-round coil springs for Jimny in Japan!
These Dual-rate Coil Springs offer excellent comfort and cornering and was made specifically for city and high-speed driving. Also, controllability can be ensured even at high-speed driving on rough off-roads. We highly recommend these Lift Coil Springs because they ensure a stable ride.
Dual-rate Coil Springs are soft when there is a slight impact and become hard when there is greater impact, always allowing for a stable and smooth ride. Designed by TANIGUCHI and CHUHATSU and tested numerous times by both computer simulations and off-road, high speed, and city driving.
Due to the longs suspension travel and low center of gravity, it's also excellent on rough roads when used with TANIGUCHI 2-3 inch lift Shock Absorbers. Made in Japan.

TANIGUCHI suspensions are highly recommended as the best performance suspension for Jimny in Japan. They are designed from Jimny's vast data and technology by TANIGUCH's 40 years of Jimny experience. They spend a lot of time testing these products with leading test drivers and these products are manufactured with top automobile makers. It is a high-performance suspension that has improved on-road and off-road driving performance, drive quality and comfort more than the SUZUKI original ones.

These products are designed for a RHD (right-hand drive) Jimny, but it is possible to install them for LHD(left-hand drive) as well. Actually, several of our LHD customers have already installed these products without any issues. If there is a difference in height between the left and right, please consider using the coil spacers. However, this has not been tested and may not work on all models. Please note this product is designed so that the right side (driver's seat side) of RHD is slightly higher when no one is on board.

Comes in a set of four Coil Springs (46,600 JPY), 40mm Suspension Kit (141,600 - 206,900 JPY).

[ Required ]
- Longer shock absorbers
- Remove front cross member, or replace with Drop Cross Member
- 50mm Extended Brake Hoses

[ Recommended ]
- Rear Adjustable Panhard Rod, or Rear Panhard Rod Relocation Bracket (both recommended)
- Front Adjustable Panhard Rod
- Caster Correction Bushes 5.0, or Caster Corrected Front Radius Arms (highly recommend)

[ Required in some cases ]
- Extended bump stop (X-large Bump Stop or Bump Stop Block etc.)
* especially for the rear when using the A14X shock absorber
- Stabilizer correction item (Offset Stabilizer Bracket etc.)
- Head Light Leveler Fixed Stay or Adjustable Head Light Leveler Rod

free length (mm)

spring rate (N/mm)

FR 383.7 21.0 / 24.0

FL 

364

21.0 / 24.0

RR

351

23.0 / 25.0

RL

332

23.0 / 25.0

Applicable vehicles: Jimny (2018-present) JB74, 64 RHD (right handle drive)
Brand: TANIGUCHI, CHUHATSU
Lift height: front 35mm, rear 40mm (JB74)
Mounting: Professional (professional installation required)

About TANIGUCHI:
Our shop trusts "Off-Road Service TANIGUCHI" is Japan's best Jimny custom parts supplier. They have manufactured more than 300 Jimny products since 1983. Especially their suspensions and drivetrains are best-performance products. TANIGUCHI spends a lot of time testing its products with leading test drivers. Also, protection, interior, and exterior products have been highly evaluated for their superior quality and thoughtful construction.

TANIGUCHI 40mm Lift Coil Springs Jimny JB74 (2018-ON)

Regular price ¥46,600 ¥0 Unit price per

We recommend these 40mm / 1.5" Lift Coil Springs as the best all-round coil springs for Jimny in Japan!
These Dual-rate Coil Springs offer excellent comfort and cornering and was made specifically for city and high-speed driving. Also, controllability can be ensured even at high-speed driving on rough off-roads. We highly recommend these Lift Coil Springs because they ensure a stable ride.
Dual-rate Coil Springs are soft when there is a slight impact and become hard when there is greater impact, always allowing for a stable and smooth ride. Designed by TANIGUCHI and CHUHATSU and tested numerous times by both computer simulations and off-road, high speed, and city driving.
Due to the longs suspension travel and low center of gravity, it's also excellent on rough roads when used with TANIGUCHI 2-3 inch lift Shock Absorbers. Made in Japan.

TANIGUCHI suspensions are highly recommended as the best performance suspension for Jimny in Japan. They are designed from Jimny's vast data and technology by TANIGUCH's 40 years of Jimny experience. They spend a lot of time testing these products with leading test drivers and these products are manufactured with top automobile makers. It is a high-performance suspension that has improved on-road and off-road driving performance, drive quality and comfort more than the SUZUKI original ones.

These products are designed for a RHD (right-hand drive) Jimny, but it is possible to install them for LHD(left-hand drive) as well. Actually, several of our LHD customers have already installed these products without any issues. If there is a difference in height between the left and right, please consider using the coil spacers. However, this has not been tested and may not work on all models. Please note this product is designed so that the right side (driver's seat side) of RHD is slightly higher when no one is on board.

Comes in a set of four Coil Springs (46,600 JPY), 40mm Suspension Kit (141,600 - 206,900 JPY).

[ Required ]
- Longer shock absorbers
- Remove front cross member, or replace with Drop Cross Member
- 50mm Extended Brake Hoses

[ Recommended ]
- Rear Adjustable Panhard Rod, or Rear Panhard Rod Relocation Bracket (both recommended)
- Front Adjustable Panhard Rod
- Caster Correction Bushes 5.0, or Caster Corrected Front Radius Arms (highly recommend)

[ Required in some cases ]
- Extended bump stop (X-large Bump Stop or Bump Stop Block etc.)
* especially for the rear when using the A14X shock absorber
- Stabilizer correction item (Offset Stabilizer Bracket etc.)
- Head Light Leveler Fixed Stay or Adjustable Head Light Leveler Rod

free length (mm)

spring rate (N/mm)

FR 383.7 21.0 / 24.0

FL 

364

21.0 / 24.0

RR

351

23.0 / 25.0

RL

332

23.0 / 25.0

Applicable vehicles: Jimny (2018-present) JB74, 64 RHD (right handle drive)
Brand: TANIGUCHI, CHUHATSU
Lift height: front 35mm, rear 40mm (JB74)
Mounting: Professional (professional installation required)

About TANIGUCHI:
Our shop trusts "Off-Road Service TANIGUCHI" is Japan's best Jimny custom parts supplier. They have manufactured more than 300 Jimny products since 1983. Especially their suspensions and drivetrains are best-performance products. TANIGUCHI spends a lot of time testing its products with leading test drivers. Also, protection, interior, and exterior products have been highly evaluated for their superior quality and thoughtful construction.

Shipping calculated at checkout.

Stock: We have a lot of products in stock, but please note some of them are the manufacturer's stock. In that case, our shop will order them after receiving your order, so the order will take 4-6 business days to ship. Also, some others are on backorder or are made-to-order and may take several weeks or more.

Shipping Cost: Our shipping cost calculation system is imperfect, and the shipping quotes in your cart are estimates. Please be aware that there may be an additional shipping cost in some rare cases. In certain areas, shipping has been temporarily suspended, or delivery to certain areas might be difficult at the present.

Compatibility: Our products are designed for RHD (right-hand drive) and JDM (Japan Domestic Market). We hope that most of our products will fit international models and LHD (left-hand drive) as well but we have not tested the compatibility of some products. Please research for yourself and ensure that the part you are purchasing is compatible with your vehicle prior to ordering.

Design: Please note the colors of the products in the photos may look different from the actual products depending on the condition of the photos and the type of displays. The specifications and design of the logo, etc. of the listed products may be subject to change for improvement.

* Please contact us for further information before purchasing.