This product corrects the mounting position of the rear Panhard rod by about 50mm downward and 12mm backward. It creates a smooth, stable ride by correcting the mounting position of the rear Panhard rod by about 50mm downward. It is also recommended when using thicker shock absorbers whose diameters are more than 30mm since it prevents the Panhard rod from hitting the shock absorber by relocating the mounting position 12mm backward.
When your Jimny is lifted, the use of the Adjustable Panhard Rod eliminates lateral displacement. But this alone does not solve the angle problem. A Panhard rod should ideally be at an angle close to horizontal. However, if the Panhard rod has become too angled by lifting, the vehicle's body sways not only up and down but also left and right when driving on bumpy roads. It also causes various problems such as unstable behavior when rolling and applying force in the direction in which the body twists during acceleration. Especially in the rear Panhard rod, these problems appear conspicuously. This product solves this angle problem by correcting the mounting position of the rear Panhard rod by about 50mm downward and creates a smooth, stable ride even in various situations. Drilling is required.
* It's also recommended as in #2 and #3 below to install both the TANIGUCHI Rear Panhard Rod Relocation Bracket, which can relocate the mounting position of the Panhard Rod 40mm upward on the Axle Housing side, with this product. It will then be possible to achieve a comfortable ride and stable driving performance even if your Jimny has been lifted by 4 inches (100mm) or more.
* Also, the Rear Panhard Rod Off-set Relocation Kit is recommended for Jimny which has been installed with thicker shock absorbers and thicker coil springs.
[ Recommended installation ]
1, Lifted 40-75mm: Using this bracket.
2, Lifted 80-120mm: Using this bracket together with the TANIGUCHI Rear Panhard Rod Relocation Bracket (40mm upward).
3, Lifted 120mm or more: Using both this bracket and the TANIGUCHI Rear Panhard Rod Relocation Bracket (40mm upward) with the Adjustable Panhard Rod.
Note: It is OK for lifted Jimny to use only this Bracket in some cases. However, to achieve the highest results of proper left and right alignment for any lifted Jimny, we recommend using both these relocation brackets and the Adjustable Panhard Rod regardless of the amount of lift.
Applicable vehicles: Jimny (2018-present) JB74, 64
Brand: MASTERPIECE
Material: Steel
Color: Black painted finish
Mounting: Professional (professional installation required)
About MASTERPIECE:
A long-established Japanese 4WD parts supplier that has developed many aftermarket off-road vehicle products mainly suspension parts. They are developing parts for many off-road vehicles such as Land Cruiser, but they have also been enthusiastic about developing Jimny parts for many years. Especially their suspension parts for hard off-road adventurers have great performance even for on-road and regular city driving, and they are loved by many enthusiasts in Japan.
MASTERPIECE Rear Panhard Rod Offset Relocation Bracket Jimny JB74 (2018-ON)
This product corrects the mounting position of the rear Panhard rod by about 50mm downward and 12mm backward. It creates a smooth, stable ride by correcting the mounting position of the rear Panhard rod by about 50mm downward. It is also recommended when using thicker shock absorbers whose diameters are more than 30mm since it prevents the Panhard rod from hitting the shock absorber by relocating the mounting position 12mm backward.
When your Jimny is lifted, the use of the Adjustable Panhard Rod eliminates lateral displacement. But this alone does not solve the angle problem. A Panhard rod should ideally be at an angle close to horizontal. However, if the Panhard rod has become too angled by lifting, the vehicle's body sways not only up and down but also left and right when driving on bumpy roads. It also causes various problems such as unstable behavior when rolling and applying force in the direction in which the body twists during acceleration. Especially in the rear Panhard rod, these problems appear conspicuously. This product solves this angle problem by correcting the mounting position of the rear Panhard rod by about 50mm downward and creates a smooth, stable ride even in various situations. Drilling is required.
* It's also recommended as in #2 and #3 below to install both the TANIGUCHI Rear Panhard Rod Relocation Bracket, which can relocate the mounting position of the Panhard Rod 40mm upward on the Axle Housing side, with this product. It will then be possible to achieve a comfortable ride and stable driving performance even if your Jimny has been lifted by 4 inches (100mm) or more.
* Also, the Rear Panhard Rod Off-set Relocation Kit is recommended for Jimny which has been installed with thicker shock absorbers and thicker coil springs.
[ Recommended installation ]
1, Lifted 40-75mm: Using this bracket.
2, Lifted 80-120mm: Using this bracket together with the TANIGUCHI Rear Panhard Rod Relocation Bracket (40mm upward).
3, Lifted 120mm or more: Using both this bracket and the TANIGUCHI Rear Panhard Rod Relocation Bracket (40mm upward) with the Adjustable Panhard Rod.
Note: It is OK for lifted Jimny to use only this Bracket in some cases. However, to achieve the highest results of proper left and right alignment for any lifted Jimny, we recommend using both these relocation brackets and the Adjustable Panhard Rod regardless of the amount of lift.
Applicable vehicles: Jimny (2018-present) JB74, 64
Brand: MASTERPIECE
Material: Steel
Color: Black painted finish
Mounting: Professional (professional installation required)
About MASTERPIECE:
A long-established Japanese 4WD parts supplier that has developed many aftermarket off-road vehicle products mainly suspension parts. They are developing parts for many off-road vehicles such as Land Cruiser, but they have also been enthusiastic about developing Jimny parts for many years. Especially their suspension parts for hard off-road adventurers have great performance even for on-road and regular city driving, and they are loved by many enthusiasts in Japan.
Stock: We have a lot of products in stock. But wheels are the manufacturer's stock or pre-order-sale. Bumpers are the manufacturer's stock or made-to-order. Some other products may be on backorder or are made-to-order. Such items may take a while to ship.
Shipping Cost: Our shipping cost calculation system is imperfect, and the shipping quotes in your cart are estimates. There may be an additional shipping cost in some rare cases.
Compatibility: Our products are designed for RHD and the Japanese domestic market. Most of our products may fit international models and LHD, but we have not tested the compatibility. Jimny 5 Door is unavailable in Japan yet, and compatibility has not been tested. Please research for yourself and ensure that the part you are purchasing is compatible with your vehicle.
Tax: Import duties, taxes, and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to buying.
Design: The colors of the products in the photos may look different from the actual products depending on the condition of the photos and the type of displays. The specifications, design, etc. of the listed products may be subject to change for improvement.
Cancellation: A cancellation fee of 5% of the order value will be charged. Pre-orders, made-to-order, and manufacturer's stock products cannot be canceled after placing the order.
Shipping Method: If you would like a specific shipping company or method, please inform us at the time of purchase. There may be an additional shipping cost depending on the company. Without any word from the buyer, we choose the company depending on the situation.
* Please check the FAQ page or our policy pages for further information before purchasing.